1996 Coats 1004 Wheel Balancer Unit is in good working order and comes with minimal cone assortment. Specifications: Cycle time 4-5 seconds, max. Outer tire diameter is 42”, wheel dia. 10” – 19.9”, wheel width 2.7” – 18.6”, modified tongue motor with: 900 RPM rating, forced air cooling, 1-1/2 HP rating, shipping weight 550 lbs. Service Manual — COATS Models 950/950 ProRacer/1025/1050/1055. 3 Preliminary Inspection 1. Check the power supply to the balancer. See the procedure on page 6. 2.The Balancer should sit on all three (3) legs. Make sure the legs have not filled with dirt, wheel weights, or other foreign matter that may prevent a leg from making contact with. Coats 1004 Computer Wheel Balancer, Model No. 8630003, SN: 08-, Volts: 220, HZ, Amps: In City Of East Haven Foreclosure Auction: Tools. Jan 17, 2019 Coats. Coats have been making wheel balancers forever! All of their early and late model automotive equipment has been first class apart. This link will take you to the Repco 471 Wheel Balancer machine operators manual and the Calibration procedure, for anyone who wants the information on the Worlds best wheel balancer I dont have a.
- Coats 1004 Wheel Balancer Manual Review
- Coats Wheel Balancer Parts
- Coats 1004 Wheel Balancer Manual Transmission
- Coats 1004 Wheel Balancer Manual Instructions
- Coats Wheel Balancers
Advertising
Connect to Power
Your factory trained COATS
®
Service Technician should do the
final check to verify the power installation before connecting the
balancer to a power supply. Failure due to improper power con-
nection will void the warranty.
balancer to a power supply. Failure due to improper power con-
nection will void the warranty.
Connect the balancer to an appropriate electrical receptacle.
Refer to Figure 8 and 9, as well as Electrical Requirements on
page 1.
page 1.
Note: If pedestrian or equipment traffic might damage the
standard power cord, power outlets must be enclosed in a race-
way on the floor or in an overhead drop.
way on the floor or in an overhead drop.
Note: Electric outlets must be solidly connected. There should
be less than 1 Ω electrical resistance between the ground pin
and earth ground. The installer or electrical inspector must ver-
ify the outlet installation before connecting the balancer. Failure
due to improper power connection will void the warranty.
and earth ground. The installer or electrical inspector must ver-
ify the outlet installation before connecting the balancer. Failure
due to improper power connection will void the warranty.
Note: The green wire in the cord is the grounding wire. Never
connect the green wire to a live terminal.
Initial Testing
This should be performed by your factory trained COATS
®
Service Technician.
1. If the circuit breaker for the balancer outlet is off, turn it on
now. Turn the balancer ON/OFF switch to ON.
Remember: To maintain the proper operating temperature for
the balancer, the unit should be left on all day.
2. The displays will show zeros when the unit is first turned
on. Press any key to continue.
3. Verify that the fan is running by placing your hand between
the arbor faceplate and the motor housing. You should feel air
coming out from around the motor housing. Do not operate the
balancer if airflow is not present when the balancer is on.
coming out from around the motor housing. Do not operate the
balancer if airflow is not present when the balancer is on.
4. Lower the hood and press START. The arbor faceplate
should spin in the direction indicated by the label at the outer
edge of the motor cover (clockwise when viewed straight on).
edge of the motor cover (clockwise when viewed straight on).
If the faceplate spins counterclockwise, turn the balancer off,
turn the circuit breaker off, and disconnect the balancer plug.
Swap two of the hot wires connected to the receptacle.
Reconnect the balancer to the receptacle, turn the circuit
breaker on, then turn the balancer on. Lower the hood and press
START and recheck the direction of the spin. The faceplate
should now be spinning in a clockwise direction.
Swap two of the hot wires connected to the receptacle.
Reconnect the balancer to the receptacle, turn the circuit
breaker on, then turn the balancer on. Lower the hood and press
START and recheck the direction of the spin. The faceplate
should now be spinning in a clockwise direction.
Note: Single-phase balancers will also spin in a clockwise
direction.
Note: Disregard a short spin cycle with HUB displayed on the
control panel during this initial testing.
5. Raise the hood during a spin cycle to verify that the hood
interlock system is functioning properly.
Direct Drive
COATS 1000/1000D Wheel Balancer • 5
Figure 8 - Three-Phase Wiring Diagram
Figure 9 - Single-Phase Wiring Diagram
Three-Phase
Ground
Hot
195-230 V
Between
Hot Wires
Between
Hot Wires
Hot
Hot
Single-Phase
A – Red
B – Black
Green/
Ground
Advertising
Popular Brands
Popular manuals
Advertising
Connect to Power
Your factory trained COATS
Coats 1004 Wheel Balancer Manual Review
®
Service Technician should do the
final check to verify the power installation before connecting the
balancer to a power supply. Failure due to improper power con-
nection will void the warranty.
balancer to a power supply. Failure due to improper power con-
nection will void the warranty.
Connect the balancer to an appropriate electrical receptacle.
Refer to Figure 8 and 9, as well as Electrical Requirements on
page 1.
page 1.
Note: If pedestrian or equipment traffic might damage the
standard power cord, power outlets must be enclosed in a race-
way on the floor or in an overhead drop.
way on the floor or in an overhead drop.
Note: Electric outlets must be solidly connected. There should
be less than 1 Ω electrical resistance between the ground pin
and earth ground. The installer or electrical inspector must ver-
ify the outlet installation before connecting the balancer. Failure
due to improper power connection will void the warranty.
and earth ground. The installer or electrical inspector must ver-
ify the outlet installation before connecting the balancer. Failure
due to improper power connection will void the warranty.
Note: The green wire in the cord is the grounding wire. Never
connect the green wire to a live terminal.
Coats Wheel Balancer Parts
Initial Testing
This should be performed by your factory trained COATS
®
Service Technician.
1. If the circuit breaker for the balancer outlet is off, turn it on
now. Turn the balancer ON/OFF switch to ON.
Remember: To maintain the proper operating temperature for
the balancer, the unit should be left on all day.
2. The displays will show zeros when the unit is first turned
on. Press any key to continue.
3. Verify that the fan is running by placing your hand between
the arbor faceplate and the motor housing. You should feel air
coming out from around the motor housing. Do not operate the
balancer if airflow is not present when the balancer is on.
coming out from around the motor housing. Do not operate the
balancer if airflow is not present when the balancer is on.
4. Lower the hood and press START. The arbor faceplate
should spin in the direction indicated by the label at the outer
edge of the motor cover (clockwise when viewed straight on).
edge of the motor cover (clockwise when viewed straight on).
If the faceplate spins counterclockwise, turn the balancer off,
turn the circuit breaker off, and disconnect the balancer plug.
Swap two of the hot wires connected to the receptacle.
Reconnect the balancer to the receptacle, turn the circuit
breaker on, then turn the balancer on. Lower the hood and press
START and recheck the direction of the spin. The faceplate
should now be spinning in a clockwise direction.
Swap two of the hot wires connected to the receptacle.
Reconnect the balancer to the receptacle, turn the circuit
breaker on, then turn the balancer on. Lower the hood and press
START and recheck the direction of the spin. The faceplate
should now be spinning in a clockwise direction.
Note: Single-phase balancers will also spin in a clockwise
direction.
Note: Disregard a short spin cycle with HUB displayed on the
Fallout 3 random crashes windows 10. control panel during this initial testing.
5. Raise the hood during a spin cycle to verify that the hood
interlock system is functioning properly.
Direct Drive
COATS 1000/1000D Wheel Balancer • 5
Coats 1004 Wheel Balancer Manual Transmission
Figure 8 - Three-Phase Wiring Diagram
Figure 9 - Single-Phase Wiring Diagram
Three-Phase
Ground
Hot
195-230 V
Between
Hot Wires
Between
Hot Wires
Hot
May 21, 2017 X-Force for Autodesk 2013 All Products Universal Keygen, Genkey for autodesk 2013. Link Download x force 2013 (32bit + 64bit, 100% work): X-Force for Autodesk 2013. Link download autocad 2013 64bit: autocad 2013 64bit. Link download autocad 2013 32bit: autocad 2013 32bit.
Hot
Coats 1004 Wheel Balancer Manual Instructions
Single-Phase
A – Red
Coats Wheel Balancers
B – Black
Green/
Ground
Advertising
Popular Brands
Popular manuals